...

How do you measure a counter with a lip or a rounded front edge?

Example thread · fictional members and dates What does this mean?

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • #5423
    GiftShop_Asheville
    Participant

    Our register sits on an old oak counter that came with the building. It has a raised lip along the front edge, about three quarters of an inch tall, and the left end is rounded where it curves toward the window.

    I want a mat that lies flat between the lip and the register. Do I measure from the inside of the lip, from the top of it, or right over it? And how do I measure a rounded end without getting out a compass?

    #5424
    PartsDesk_Wichita
    Participant

    Our parts counter has a steel bump rail on the front, so I’ve done this. Measure the flat surface where the mat will actually lie, at the bottom of the lip, not at the top edge. Lips on old counters lean in or out a little, and the top can be off by half an inch from the bottom.

    Take the depth in three places: both ends and the middle. Old counters are rarely square. Use the smallest of the three numbers.

    #5425
    Designer_PDX
    Participant

    Then leave clearance. A mat cut to the exact inside measurement rides up against the lip and starts to curl at the edge within a few weeks. I tell clients to take about a quarter inch off every side that touches a lip or a wall.

    For the rounded end, skip the math and make a paper template. Tape a few sheets of kraft paper together, lay them on the counter, press the paper into the curve and trace it with a pencil. Cut along the line, put it back on the counter and trim until it sits flat. The template becomes your measurement.

    #5426
    GiftShop_Asheville
    Participant

    Just measured with a proper tape. Inside the lip at the bottom I get 21 and a quarter inches at the right end, 21 and three quarters in the middle and 21 and a half at the left. So the counter isn’t square, like PartsDesk_Wichita said.

    Should the mat go up and over the lip? It would look tidier from the customer side.

    #5427
    PartsDesk_Wichita
    Participant

    I wouldn’t. A mat over a lip never lies flat. The edge lifts, catches sleeves and bag straps, and starts curling. We tried it once over the bump rail, and the hand truck caught the edge on the first busy morning. Stop the mat short of the lip and let the lip do its job.

    Measure the lip height too. If the mat ends up taller than the lip, pens and coins slide right off the front again, and the lip stops being useful.

    #5428
    Designer_PDX
    Participant

    On the rounded end you have two choices. Stop the mat square, just before the curve starts, or have it cut to follow the curve.

    Square is simpler and usually cheaper, because it’s a standard rectangle. A curved end looks built in, but it’s a custom shape, and your template has to be accurate. If the curve area holds something anyway, like a display or a plant, square is the easy answer.

    #5429
    GiftShop_Asheville
    Participant

    Made the template last night with my kids’ leftover craft paper. The curve starts about nine inches from the left end. I’m leaning toward stopping the mat square there, because that corner holds the candle display anyway.

    #5430
    CounterMats Team
    Moderator

    The paper template is the best tool in this thread, and PartsDesk_Wichita’s three-point depth check is how we’d measure as well.

    Our measuring guide follows the same order. Start with the full counter length. Measure permanent equipment separately. Take the width where the mat will lie. Then look at gaps and overhangs, which make a mat curl or lift, and at rounding and odd shapes. For a counter with a lip, measure the flat surface at the bottom of the lip, not the top.

    Most counters take a mat between 18 and 30 inches deep, so a lip that eats into that depth matters. Our standard printed sizes are 12 x 18, 16 x 20 and 18 x 24 in. A curved end or a size between those is a custom size or shape, and we quote it. Send a photo of the template on the counter with your measurements. Every printed order gets a free digital proof within 1 business day, so you see the shape before anything prints. The minimum order is 50 mats.

    How to measure your counter, step by step: https://countermats.com/how-to-measure-your-counter-for-a-custom-counter-mat/

    CounterMats Team · Contact Us

    #5431
    GiftShop_Asheville
    Participant

    So my working numbers: the smallest depth is 21 and a quarter, minus a quarter inch for clearance, which gives me 21 inches. For length I measure from the right wall to where the curve starts, minus the same quarter inch.

    Does the register sit on the mat or beside it? That changes the length.

    #5432
    PartsDesk_Wichita
    Participant

    Beside it, if you can. A register or a heavy terminal on top of a mat presses a dent into it, and the mat slides every time someone pulls the drawer. We cut around our parts computer and keep the mat on the open working area.

    If the register has to sit on the mat, measure its footprint and mark it on your sketch so the design doesn’t put the logo under it.

    #5433
    Designer_PDX
    Participant

    Write it all on one sketch: counter outline, lip, register footprint, where the curve starts and which edge faces the customer. Put every number on it and photograph it next to the counter with the tape measure in the shot. A printer can work from that without guessing, and you’ll have it the next time you need a mat.

    Mark the customer side clearly. I’ve seen a design come back upside down from the shopper’s point of view because nobody wrote down which way people stand.

    #5434
    GiftShop_Asheville
    Participant

    Sketch done, with the register beside the mat and the customer edge marked with a big arrow. Final working size is 21 by 38 inches, square end, a quarter inch off every side that meets the lip or wall.

    #5435
    PartsDesk_Wichita
    Participant

    That’s a clean set of numbers. Check one thing before you send it: the seam. Old counters often have a joint between boards. A slight ridge disappears under a mat, but a raised step shows through and becomes the spot where the edge starts lifting.

    #5436
    GiftShop_Asheville
    Participant

    There is a seam, about two feet in from the wall, but it’s flush. I ran my thumbnail across it and felt nothing. I’ll note it on the sketch anyway.

    #5437
    Designer_PDX
    Participant

    Good. With the seam noted, the counter is fully described. Keep the template rolled up somewhere safe, because the next mat will need the same measurements and the counter won’t get any more square.

Viewing 15 posts - 1 through 15 (of 15 total)
  • Log in or create an account to post. Anyone can read.

Log in

Forgot your password?

Join the Counter Mat Forum

Everyone sees this. A role works well instead of your name, for example CStore_Owner_Ohio.

Members, discussions and dates in threads marked Example thread are fictional. CounterMats wrote them to explain common counter mat questions in plain language.

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.