...

Standard size or custom cut for an L-shaped service desk?

Example thread · fictional members and dates What does this mean?

Viewing 16 posts - 1 through 16 (of 16 total)
  • Author
    Posts
  • #5503
    ServiceMgr_Edison
    Participant

    Our service drive just got a new desk. It’s an L shape. The long side faces the lane where customers pull in, and the short side turns toward the waiting area where the advisors go over the repair order. Each advisor has a monitor, a keyboard, a printer for repair orders and a key box. Customers lean on the corner while they sign.

    I want a mat on it, partly to protect the new laminate and partly so customers have something to look at besides the clock. Do I go with a standard rectangle on each leg, or have one cut to the L shape? I’ve never had anything custom-cut made and I don’t know what I’m getting into.

    #5504
    FrontOffice_Vegas
    Participant

    Our front desk is an L too, and we went through the same debate. Start with where people actually stand. On ours, nobody uses the short leg except staff. Guests check in along the long side, sign at two spots, and that’s it.

    So before you think about the shape, stand at the desk for an hour on a busy morning and note where hands and papers land. The mat needs to cover those spots, not the whole desk.

    #5505
    ServiceMgr_Edison
    Participant

    Fair. On mine the corner is the busiest spot, though. That’s where the advisor turns the screen around and the customer signs.

    #5506
    PartsDesk_Wichita
    Participant

    Then the corner is your problem spot. Two rectangles that meet at a corner leave a seam right where people push paper and slide keys. On my parts counter, the seam between two mats collects grit and the edge lifts after a few months. Every catalog that gets dragged across it catches.

    If the corner is where the work happens, either one piece covers it or you leave the corner bare and put mats on the straight runs.

    #5507
    Designer_PDX
    Participant

    From the print side, a custom L shape is doable, but the artwork gets trickier. A rectangle has one “up” direction. An L has two readers: someone on the long side and someone on the short side read it from different angles. If the design has text, decide which side reads it. Usually the customer side wins and the staff side gets a logo or nothing.

    Also think about the inside corner. A sharp inside corner on a cut piece is a weak spot where tears start. Ask the printer whether they round it. Most cut shapes have a small radius there.

    #5508
    ServiceMgr_Edison
    Participant

    How do I even measure an L for a quote? Two lengths and a depth?

    #5509
    Designer_PDX
    Participant

    Four numbers at least, and a sketch. Outside length of the long leg, outside length of the short leg, depth of each leg (they’re often different), and where the equipment sits. Measure from the outside edges, draw it on paper with the numbers on it and take a photo from above. A sketch with numbers prevents more mistakes than any form field.

    If the front edge has a lip or a rounded nose, note that too and measure only the flat part.

    #5510
    PartsDesk_Wichita
    Participant

    And measure twice, on different days. Our parts counter looked square until we measured the depth at both ends. Almost half an inch off from one end to the other. Old building, and nobody had ever checked.

    #5511
    FrontOffice_Vegas
    Participant

    Replacement is what pushed us toward standard sizes. With two standard rectangles, when the one where guests sign wears out, we replace that one. With one big custom piece, the whole thing goes. On a desk that runs 24 hours, the signing spot wears out years before the rest of the mat.

    #5512
    ServiceMgr_Edison
    Participant

    That’s a good argument. Our advisors are rough on the corner. Coffee, keys, clipboards, the occasional muffler gasket somebody brings up from the shop.

    #5513
    CounterMats Team
    Moderator

    For an L-shaped desk, both routes work, and the trade-offs above are the real ones: a single cut piece avoids the corner seam, and separate rectangles are easier to replace one at a time.

    Our standard printed sizes are 12 x 18 in, 16 x 20 in and 18 x 24 in. Most counters take a mat between 18 and 30 inches deep, so measure the depth of each leg separately before you pick. Custom sizes and shapes, including an L cut, are quoted. Send the sketch with the four measurements Designer_PDX lists and mark where the monitors and the printer sit.

    We charge no setup fees, and every printed order gets a free digital proof within 1 business day, so you can check how the artwork reads from each side of the L before anything prints. The minimum order is 50 mats.

    Our page on sizes covers what standard sizes actually cover, when a custom size earns its cost, why measuring correctly matters more than the choice itself, and how thickness is part of sizing: https://countermats.com/counter-mat-sizes/

    CounterMats Team · Contact Us

    #5514
    ServiceMgr_Edison
    Participant

    Fifty is more than one desk, but our group has six stores with the same service desk from the same remodel. If the shape works here, it works at all of them, plus the parts counters and the cashier window.

    #5515
    PartsDesk_Wichita
    Participant

    If you go to six stores, measure all six. “Same layout” is what we were told too, and two of our counters turned out to be built by a different contractor with a different idea of square.

    #5516
    FrontOffice_Vegas
    Participant

    Same here. Our sister property’s desk looked identical in the drawings and came out three inches shorter on the short leg. A mat cut for our desk would have hung off theirs.

    #5517
    Designer_PDX
    Participant

    If the sizes differ by store, a standard rectangle on the long side plus a custom piece only where needed keeps the artwork simpler. One design, cropped two ways, instead of six versions of an L that each need their own proof.

    #5518
    ServiceMgr_Edison
    Participant

    Here’s where I landed. I’m measuring all six desks this week with the four numbers and a sketch for each. If the corners match, we quote one L shape with the customer-facing text on the long leg. If they don’t, standard rectangles on the long side and a bare corner. Either way the advisors stop spilling coffee on new laminate.

Viewing 16 posts - 1 through 16 (of 16 total)
  • Log in or create an account to post. Anyone can read.

Log in

Forgot your password?

Join the Counter Mat Forum

Everyone sees this. A role works well instead of your name, for example CStore_Owner_Ohio.

Members, discussions and dates in threads marked Example thread are fictional. CounterMats wrote them to explain common counter mat questions in plain language.

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.