...

What survives a parts counter with grease and heavy parts on it?

Example thread · fictional members and dates What does this mean?

Viewing 16 posts - 1 through 16 (of 16 total)
  • Author
    Posts
  • #5784
    PartsDesk_Wichita
    Participant

    Parts counter at a truck and equipment dealership. Brake rotors, hydraulic fittings, the odd starter, and every one of them comes in with grease on it. Techs drop parts on the counter, customers lean on it, and the parts catalogs live on it.

    We’ve gone through three mats in two years. One cracked, one got cut by a rotor edge, one turned into a grease sponge. What actually survives a counter like this?

    I’m not after anything fancy. I want the counter protected, the catalogs off the bare laminate, and something that doesn’t look like a shop rag by Friday. A logo and our phone number would be nice. Survival comes first.

    #5785
    ServiceMgr_Edison
    Participant

    Different counter, same building type. Our service desk sees keys, paperwork and customers’ elbows, not rotors. Even so, the mat that lasted was the heavy rubber one, not the nice-looking printed one. The printed one lasted a year before the edges went.

    For a parts counter I’d want heavy rubber or something like it, with no fabric anywhere.

    #5786
    PartsDesk_Wichita
    Participant

    The grease sponge was fabric on top. Agreed on no fabric. The cracked one was a hard plastic. Got cold in the winter and a dropped part split it.

    #5787

    Your cleaner matters as much as the mat. What do the guys use on the counter?

    #5788
    PartsDesk_Wichita
    Participant

    Whatever degreaser is in the shop. Sometimes brake cleaner, if I’m honest.

    #5789

    That explains part of it. Brake cleaner and strong solvents attack a lot of mat materials, rubber included. The surface goes tacky or hard and cracks. Your cracked mat may not have been the cold alone. A surface that’s been dried out by solvent for a year breaks much more easily when something heavy hits it on a January morning. For the mat, use a mild degreaser at the strength on the label, wipe, and rinse with a damp cloth. Keep brake cleaner for brakes.

    And lift the mat once a week. Grease migrates under a mat and sits there. That’s half of the smell people blame on the mat itself.

    #5790
    ServiceMgr_Edison
    Participant

    What about the cut? A sharp rotor edge will cut almost anything if somebody drags it.

    #5791
    PartsDesk_Wichita
    Participant

    That’s on us. Rotors get dragged across. I’ve told the techs to set them down and lift them off, not slide. Habits take a while.

    The other half is where they land. Techs come from the shop door on the right, so the right end of the counter takes every heavy part. The left end, by the catalogs, barely gets touched. Looking at the old mats, all the damage is in the right third.

    #5792
    CounterMats Team
    Moderator

    A parts counter is one of the hardest places to put a mat, and the cleaning point from ClinicFacilities_PHX matters as much as the material choice.

    Our dealership page covers how the service desk wait really works and the parts side of the building too: what earns attention on a dealership mat, the abuse that comes with the job, the multi-location problem for dealer groups, and what we would order for a service desk: https://countermats.com/dealership-counter-mats/

    For size, the largest standard printed size is 18 x 24 in, and a custom size or shape is quoted. For specials that change, the Stock Interchangeable mat comes in 10.5 x 13 in with an 8.5 x 11 insert and 13 x 19 in with an 11 x 17 insert. Send the counter measurements and a photo of what sits on it, and we’ll quote what fits.

    CounterMats Team · Contact Us

    #5793
    PartsDesk_Wichita
    Participant

    Counter is 96 inches long and 30 deep. Catalog stand takes the left 20 inches. So the working area is about 70 by 24 after you leave room at the front edge for the customer’s arms.

    That’s longer than any standard mat. I may go with two mats end to end.

    #5794
    ServiceMgr_Edison
    Participant

    Two mats is easier to clean and replace, too. If one end takes all the damage, which it will, you swap that one. On our desk, the end by the key drop wears out first. Same idea.

    You could even go further. A plain heavy rubber drop pad on the right end where techs set parts, and a printed mat on the left two-thirds where customers stand. The drop pad is the sacrificial one. The printed mat lives a lot longer when nothing heavy lands on it.

    #5795

    Two mats also means you can rotate them. Swap left and right every few months so the wear spreads out. We do that with floor mats at clinic entrances and they last noticeably longer.

    #5796
    PartsDesk_Wichita
    Participant

    Rotation I can do, and the drop pad idea is better than what I had. Here’s what I’m going with:

    • Heavy rubber, no fabric, no hard plastic
    • Plain drop pad on the right end where parts land
    • Printed mat on the customer side of the rest of the counter
    • Rotate the mats every quarter where the sizes allow
    • Mild degreaser at label strength, no brake cleaner on the mat
    • Lift and clean under it every week
    • Parts get set down and lifted, not dragged
    • Dark color, so the grease that’s left doesn’t show as much
    #5797
    ServiceMgr_Edison
    Participant

    Dark is right. We tried a light gray once. It looked filthy in a month even when it was clean.

    What goes on the print, if anything? On our desk, the scheduling QR does the work. At a parts counter maybe the parts hours and a QR to the online catalog.

    #5798
    PartsDesk_Wichita
    Participant

    Online catalog QR and our phone number, near the customer edge. Parts hours change twice a year, so those go on an insert at the register end instead.

    #5799

    Keep the print away from the spot where parts land. Put it in the strip nearest the customer. Ink in the drop zone wears off first no matter what the mat is made of.

    And keep a log of when each mat goes down. Write the date on the underside. Next time you’re replacing one, you’ll know whether it lasted eight months or two years, and you’ll have a real number to compare the next mat against.

Viewing 16 posts - 1 through 16 (of 16 total)
  • Log in or create an account to post. Anyone can read.

Log in

Forgot your password?

Join the Counter Mat Forum

Everyone sees this. A role works well instead of your name, for example CStore_Owner_Ohio.

Members, discussions and dates in threads marked Example thread are fictional. CounterMats wrote them to explain common counter mat questions in plain language.

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.