Forum Replies Created
- AuthorPosts
- August 5, 2026 at 5:20 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5797
ServiceMgr_Edison
ParticipantDark is right. We tried a light gray once. It looked filthy in a month even when it was clean.
What goes on the print, if anything? On our desk, the scheduling QR does the work. At a parts counter maybe the parts hours and a QR to the online catalog.
August 5, 2026 at 1:05 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5794ServiceMgr_Edison
ParticipantTwo mats is easier to clean and replace, too. If one end takes all the damage, which it will, you swap that one. On our desk, the end by the key drop wears out first. Same idea.
You could even go further. A plain heavy rubber drop pad on the right end where techs set parts, and a printed mat on the left two-thirds where customers stand. The drop pad is the sacrificial one. The printed mat lives a lot longer when nothing heavy lands on it.
August 4, 2026 at 3:10 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5790ServiceMgr_Edison
ParticipantWhat about the cut? A sharp rotor edge will cut almost anything if somebody drags it.
August 4, 2026 at 9:15 am in reply to: What survives a parts counter with grease and heavy parts on it? #5785ServiceMgr_Edison
ParticipantDifferent counter, same building type. Our service desk sees keys, paperwork and customers’ elbows, not rotors. Even so, the mat that lasted was the heavy rubber one, not the nice-looking printed one. The printed one lasted a year before the edges went.
For a parts counter I’d want heavy rubber or something like it, with no fabric anywhere.
ServiceMgr_Edison
ParticipantOurs is a QR that only exists on the mat. Scans went up after we moved the code from the top edge to the edge nearest the customer. Easy test for you at one branch before you do all nine.
ServiceMgr_Edison
ParticipantSame at our desk. Specials that change monthly go on an insert. The printed part is the brand and the scheduling QR.
One more thing on the fixed part. Keep it short enough to read in a few seconds from where the member stands. Our first mat had a paragraph about our service department. Nobody read it. The second one says “Book your next service in 30 seconds” next to the QR code, and that’s the one people scan.
ServiceMgr_Edison
ParticipantAnd think about what the member is doing in that spot. At our desk they sign the repair order. A mat that gives a smooth writing surface gets used. A mat with a heavy texture under a pen gets moved aside.
ServiceMgr_Edison
ParticipantDealership service desk. Customers stand there five minutes on a good day, longer when the advisor is looking up a recall. A mat with our service specials and a QR code for scheduling sits right where they lean.
What made it work was deciding what the mat area is for. It’s for the customer. Paperwork goes on the other side of the keyboard. Took a month of reminding the advisors.
September 18, 2025 at 12:50 pm in reply to: Standard size or custom cut for an L-shaped service desk? #5518ServiceMgr_Edison
ParticipantHere’s where I landed. I’m measuring all six desks this week with the four numbers and a sketch for each. If the corners match, we quote one L shape with the customer-facing text on the long leg. If they don’t, standard rectangles on the long side and a bare corner. Either way the advisors stop spilling coffee on new laminate.
September 17, 2025 at 1:40 pm in reply to: Standard size or custom cut for an L-shaped service desk? #5514ServiceMgr_Edison
ParticipantFifty is more than one desk, but our group has six stores with the same service desk from the same remodel. If the shape works here, it works at all of them, plus the parts counters and the cashier window.
September 17, 2025 at 9:00 am in reply to: Standard size or custom cut for an L-shaped service desk? #5512ServiceMgr_Edison
ParticipantThat’s a good argument. Our advisors are rough on the corner. Coffee, keys, clipboards, the occasional muffler gasket somebody brings up from the shop.
September 16, 2025 at 2:30 pm in reply to: Standard size or custom cut for an L-shaped service desk? #5508ServiceMgr_Edison
ParticipantHow do I even measure an L for a quote? Two lengths and a depth?
September 16, 2025 at 10:20 am in reply to: Standard size or custom cut for an L-shaped service desk? #5505ServiceMgr_Edison
ParticipantFair. On mine the corner is the busiest spot, though. That’s where the advisor turns the screen around and the customer signs.
- AuthorPosts