...

Forum Replies Created

Viewing 24 posts - 1 through 24 (of 24 total)
  • Author
    Posts
  • in reply to: Rubber, vinyl or fabric top: what holds up on a bar rail? #5701
    BarManager_Austin
    Participant

    Already know which closer that is. Dates going on tonight.

    BarManager_Austin
    Participant

    Here’s my plan. Rubber stays under the wells, where it’s always soaked. Fabric top on the guest rail, two sets, swap every night, rinse and hang the off set. Sealed edges. Solid backing. Low-pressure rinse only. If the fabric set doesn’t make it through summer, I go back to printed rubber on the rail.

    BarManager_Austin
    Participant

    Reading it now. Foam I can rule out on a bar rail, nobody wants that soaking up well water.

    in reply to: Rubber, vinyl or fabric top: what holds up on a bar rail? #5691
    BarManager_Austin
    Participant

    So the pattern is: fabric where it’s mostly dry, rubber where it’s wet. My rail is wet from 5 p.m. to close.

    BarManager_Austin
    Participant

    That’s my worry too. Rubber at least gets rinsed and goes back down.

    in reply to: What size bar mat fits behind a service well? #5685
    BarManager_Austin
    Participant

    Did the cardboard test tonight, mostly to prove you wrong. It stayed put but the right end got clipped twice by the tray stand. Taking another inch off that side.

    in reply to: What size bar mat fits behind a service well? #5683
    BarManager_Austin
    Participant

    Our logo is a wordmark with a small icon, so one line works. Here’s where I landed, in case it helps the next person:

    • Measure the flat part only, after the lip
    • Take off anything bolted down
    • Leave room at each end where trays and hips pass
    • Ledges and odd stations are usually custom; back bars are often close to standard
    • One-line logo on narrow mats
    • Ribbed or drained top where drinks land
    in reply to: What size bar mat fits behind a service well? #5681
    BarManager_Austin
    Participant

    Good point on the top. The ledge gets more spills than anywhere else because servers grab four glasses at once.

    Back bar numbers, for anyone else measuring: the build area is 18 inches deep and about 40 long, but the ice bin lip takes 2 inches and the cutting board lives on the left third. So the mat space is roughly 16 deep and 24 long. That one looks close to a standard service mat size.

    in reply to: What size bar mat fits behind a service well? #5678
    BarManager_Austin
    Participant

    Fifty mats is more than one bar uses. Between the ledge, the back bar and a couple of spares, we’d go through maybe eight a year.

    in reply to: What size bar mat fits behind a service well? #5676
    BarManager_Austin
    Participant

    Measured again with the lip in mind. The flat part is 5 inches deep, not 6. Length is 30, but the end near the POS has a ticket printer bolted on, so the usable run is about 25 inches. With a gap on each end I’m looking at something like 5 x 23. Nobody keeps that on a shelf, right?

    in reply to: What size bar mat fits behind a service well? #5673
    BarManager_Austin
    Participant

    That matches what I see. The rail runner on the guest side is narrow and long and fits fine. The ledge is the problem child. What do you leave around the edges? Flush to the ends, or a gap?

    in reply to: Can bar mats go in the dishwasher? #5650
    BarManager_Austin
    Participant

    Here’s the closing routine at my bar, for anyone who finds this. Pull the mats. Rinse the big stuff into the floor drain. Soak if there’s syrup. One cycle in the machine, flat and ridges up. Hang them on the rack overnight. They go back down at open. About two minutes per mat.

    Once a month we also check every mat for cracks and tears along the ridges. A cracked mat holds dirt in the crack no matter how you wash it, and it’s time for a new one.

    in reply to: Can bar mats go in the dishwasher? #5647
    BarManager_Austin
    Participant

    Dry them flat or hanging, not folded over the edge of the sink. Wet rubber folded overnight keeps the bend. We hang ours over a dowel on the dry rack, ridges out, so air gets to both sides. By the morning crew they’re bone dry.

    in reply to: Can bar mats go in the dishwasher? #5643
    BarManager_Austin
    Participant

    The spray reaches the grooves better. The gunk lives in the grooves, especially sugar from soda syrup. Ridges down, the flat back gets clean and the grooves stay sticky.

    If your machine has a separate rinse arm on top, it helps to run the mats in their own rack. Packed in with trays, the spray doesn’t reach half the surface, and you end up washing them twice.

    in reply to: Can bar mats go in the dishwasher? #5641
    BarManager_Austin
    Participant

    That matches what I’ve seen. In a commercial machine, lay it flat on the rack, ridges up, and don’t fold it. A folded mat comes out with a crease that never goes away.

    in reply to: Can bar mats go in the dishwasher? #5639
    BarManager_Austin
    Participant

    Then test one. Run a single mat through one cycle, flat, and look at it when it comes out. If it’s flat and the edges aren’t curled, the second one goes in tomorrow. If it curls, hand wash from now on, and you’ve only lost one test.

    in reply to: Can bar mats go in the dishwasher? #5637
    BarManager_Austin
    Participant

    Plenty of bars put rubber mats through the dish machine. Mine go through after close every night, as long as they fit the rack. But “rubber mat” covers a lot of products, and some don’t like the heat. Check the care label or the maker’s instructions first. If it says hand wash, believe it.

    The thin, floppy ones are the ones I’d worry about. Thick molded mats usually come through a commercial cycle without trouble. Thin ones can come out wavy, and a wavy mat under a soda machine is a trip hazard and a spill channel at the same time.

    BarManager_Austin
    Participant

    Behind my bar, mats get replaced when they curl or the logo’s gone, roughly once a year. When you replace, replace every mat in the same room at once. One new mat next to an old one makes the old one look worse than it is. Your counter is gentler but wiped more often. Plan for a year and be pleasantly surprised.

    BarManager_Austin
    Participant

    Watch where people wipe. My staff scrub hardest at the corners and along the front edge, because that’s where the sticky stuff collects. The print fails there first. Keep your logo and instructions in the middle and leave the edges plain.

    BarManager_Austin
    Participant

    From behind a bar, the question is what lands on the mat. Fabric tops soak up everything. A dye-sub fabric mat looks sharp on day one and smells like sour mix by Friday. We use rubber behind the bar, and the surface print on our logo mats wears first where the bottles hit the well.

    So for a bar, liquid decides it. For a check-in desk, I’d ask what your cleaning liquid does to fabric.

    BarManager_Austin
    Participant

    A month in. The printed runner that was fading hasn’t gotten worse, and the one that was fine still looks new. The closers say the soft brush is actually faster because they don’t have to rinse out the green pad gunk. Checklist stays.

    BarManager_Austin
    Participant

    OK, new close checklist for the runners, taped inside the cabinet under the well:
    1. Rinse warm
    2. Dish soap, soft brush, no green pad
    3. Rinse again
    4. Hang over the rail to dry
    5. Sanitizer at label strength only

    The green pads are banned from the bar. I’ll keep them for the floor drains.

    BarManager_Austin
    Participant

    Soft brush, mild soap, proper mix. I can train that. What about the dish machine? Half my staff wants to throw the runners in with the glass racks.

    BarManager_Austin
    Participant

    Checked with the closers. They use whatever’s in the spray bottle under the well, which is sometimes the sanitizer and sometimes a degreaser someone mixed too strong. And they scrub with the green pad.

Viewing 24 posts - 1 through 24 (of 24 total)

Members, discussions and dates in threads marked Example thread are fictional. CounterMats wrote them to explain common counter mat questions in plain language.

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.