Forum Replies Created
- AuthorPosts
- August 6, 2026 at 8:10 am in reply to: What survives a parts counter with grease and heavy parts on it? #5798
PartsDesk_Wichita
ParticipantOnline catalog QR and our phone number, near the customer edge. Parts hours change twice a year, so those go on an insert at the register end instead.
August 5, 2026 at 4:00 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5796PartsDesk_Wichita
ParticipantRotation I can do, and the drop pad idea is better than what I had. Here’s what I’m going with:
- Heavy rubber, no fabric, no hard plastic
- Plain drop pad on the right end where parts land
- Printed mat on the customer side of the rest of the counter
- Rotate the mats every quarter where the sizes allow
- Mild degreaser at label strength, no brake cleaner on the mat
- Lift and clean under it every week
- Parts get set down and lifted, not dragged
- Dark color, so the grease that’s left doesn’t show as much
August 5, 2026 at 11:45 am in reply to: What survives a parts counter with grease and heavy parts on it? #5793PartsDesk_Wichita
ParticipantCounter is 96 inches long and 30 deep. Catalog stand takes the left 20 inches. So the working area is about 70 by 24 after you leave room at the front edge for the customer’s arms.
That’s longer than any standard mat. I may go with two mats end to end.
August 4, 2026 at 4:25 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5791PartsDesk_Wichita
ParticipantThat’s on us. Rotors get dragged across. I’ve told the techs to set them down and lift them off, not slide. Habits take a while.
The other half is where they land. Techs come from the shop door on the right, so the right end of the counter takes every heavy part. The left end, by the catalogs, barely gets touched. Looking at the old mats, all the damage is in the right third.
August 4, 2026 at 12:20 pm in reply to: What survives a parts counter with grease and heavy parts on it? #5788PartsDesk_Wichita
ParticipantWhatever degreaser is in the shop. Sometimes brake cleaner, if I’m honest.
August 4, 2026 at 10:05 am in reply to: What survives a parts counter with grease and heavy parts on it? #5786PartsDesk_Wichita
ParticipantThe grease sponge was fabric on top. Agreed on no fabric. The cracked one was a hard plastic. Got cold in the winter and a dropped part split it.
September 17, 2025 at 3:10 pm in reply to: Standard size or custom cut for an L-shaped service desk? #5515PartsDesk_Wichita
ParticipantIf you go to six stores, measure all six. “Same layout” is what we were told too, and two of our counters turned out to be built by a different contractor with a different idea of square.
September 16, 2025 at 4:20 pm in reply to: Standard size or custom cut for an L-shaped service desk? #5510PartsDesk_Wichita
ParticipantAnd measure twice, on different days. Our parts counter looked square until we measured the depth at both ends. Almost half an inch off from one end to the other. Old building, and nobody had ever checked.
September 16, 2025 at 11:45 am in reply to: Standard size or custom cut for an L-shaped service desk? #5506PartsDesk_Wichita
ParticipantThen the corner is your problem spot. Two rectangles that meet at a corner leave a seam right where people push paper and slide keys. On my parts counter, the seam between two mats collects grit and the edge lifts after a few months. Every catalog that gets dragged across it catches.
If the corner is where the work happens, either one piece covers it or you leave the corner bare and put mats on the straight runs.
May 22, 2025 at 10:40 am in reply to: How do you measure a counter with a lip or a rounded front edge? #5435PartsDesk_Wichita
ParticipantThat’s a clean set of numbers. Check one thing before you send it: the seam. Old counters often have a joint between boards. A slight ridge disappears under a mat, but a raised step shows through and becomes the spot where the edge starts lifting.
May 21, 2025 at 1:00 pm in reply to: How do you measure a counter with a lip or a rounded front edge? #5432PartsDesk_Wichita
ParticipantBeside it, if you can. A register or a heavy terminal on top of a mat presses a dent into it, and the mat slides every time someone pulls the drawer. We cut around our parts computer and keep the mat on the open working area.
If the register has to sit on the mat, measure its footprint and mark it on your sketch so the design doesn’t put the logo under it.
May 20, 2025 at 2:20 pm in reply to: How do you measure a counter with a lip or a rounded front edge? #5427PartsDesk_Wichita
ParticipantI wouldn’t. A mat over a lip never lies flat. The edge lifts, catches sleeves and bag straps, and starts curling. We tried it once over the bump rail, and the hand truck caught the edge on the first busy morning. Stop the mat short of the lip and let the lip do its job.
Measure the lip height too. If the mat ends up taller than the lip, pens and coins slide right off the front again, and the lip stops being useful.
May 20, 2025 at 10:25 am in reply to: How do you measure a counter with a lip or a rounded front edge? #5424PartsDesk_Wichita
ParticipantOur parts counter has a steel bump rail on the front, so I’ve done this. Measure the flat surface where the mat will actually lie, at the bottom of the lip, not at the top edge. Lips on old counters lean in or out a little, and the top can be off by half an inch from the bottom.
Take the depth in three places: both ends and the middle. Old counters are rarely square. Use the smallest of the three numbers.
January 16, 2025 at 8:48 am in reply to: How thick should a mat be at a register that gets slammed all day? #5237PartsDesk_Wichita
ParticipantSounds right for a c-store. Come visit a parts counter sometime if you want to see what thick really means.
January 14, 2025 at 4:20 pm in reply to: How thick should a mat be at a register that gets slammed all day? #5231PartsDesk_Wichita
ParticipantYes. If customers sign paper slips or write on the counter, a very thick soft mat makes the pen push through and the signature looks drunk. We still have a few customers who sign on paper. For a register, I’d stay around a quarter inch or under. Thicker than that, and it starts to feel like a step.
The other thing with very thick mats is the edge height. Cups and bottles that get set half on the edge tip over. At a parts counter, nobody sets a coffee down. At a c-store with a coffee bar, half your customers are holding one.
January 14, 2025 at 9:15 am in reply to: How thick should a mat be at a register that gets slammed all day? #5226PartsDesk_Wichita
ParticipantI’ll second that from the parts side. We set brake rotors, water pumps and catalogs on the counter all day. A thin mat got cut by a rotor edge in the first week. A thicker rubber mat takes the hit and springs back. If heavy or sharp things touch your counter, go thicker.
- AuthorPosts